Fast Forward
www.fastforward.ca
Fast Forward Automotive

Email

Visit HasenWerk

Contact Information

Signal Processors, Gateways and Converters

Often times you need to convert one engine signal from one format to another. Fast Forward Automotive has you covered for Signal Processors and Signal Converters.

Hasenwerk CAN2 and 2CAN Series of CAN Bus Gateways

The CAN2 and 2CAN series of CAN bus gateways takes information from the Volkswagen / Audi CAN bus and converts it into signals that your non-CAN vehicle can use. The 2CAN Series also provides the missing and very necessary VSS input for all 2006 and later ECUs

Compatible with 1999.5 to 2015 ECUs

Click Here for even more Information!


CAN2LED
The CAN2LED gateway reads the ECU's CAN bus and generates the following conventional signals:

Engine Status Lights
- Check Engine Light and Glow Plug
- Up to 5W

CAD $199.95

USD $149.95

Instruction Manuals Hasenwerk CAN2LED V1.0 to 1.1
Hasenwerk CAN2LED
CAN2LED


CAN2DASH
Newly updated for 2017! CAN2DASH reads 1999.5 to 2005 ECU CAN bus and generates the following conventional signals:

Engine Status Lights
- Check Engine Light and Glow Plug
- Up to 5W
Tachometer
- Both coil driven and conventional
- Selectable between 4-6-8 cylinders

This CAN bus gateway also features a status LED and High Quality Deutsch Connectors.

CAD $349.95

USD $259.95

Instruction Manuals

Hasenwerk CAN2DASH Series v1
Hasenwerk CAN2DASH Series v2

CAN2DASH-
CAN2DASH


DASH2CAN
New for 2017 ! ! !
After more than a year and development our DASH2CAN gateway is finally available. This gateway enables two way CAN bus communications for 2006 to 2015 ECUs and provides the following functionality:

Conventional to CAN input:
- 5V to 12V Vehicle Speed Sensor to CAN with calibration
- Cruise Control: ON|OFF / Set / Resume to CAN
- Routine for steering and ABS input so ECU stays out of "Diesel Gate" mode and gives you full power.

This CAN bus gateway also features a status LED and High Quality Deutsch Connectors.

CAD $349.95

USD $259.95

Receive 15% off if you buy the CAN2DASH and DASH2CAN as a pair!

Instruction Manuals

Hasenwerk DASH2CAN manual coming soon . . .

 

Cruise Control Converter
Hasenwerk DASH2CAN
CAN Bus Gateways
Canadian Customers
CAN Bus Gateways
USA / Int'l Customers

Hasenwerk Signal Processors

To do an engine conversion right, you need to be able to accurately convert or calibrate a lot of different signals. We have signal processors for just about every need. Speed, cruise control, tachometers, instrument pods.

Hasenwerk Digital to Analog Tachometer Converter

This tachometer adapter enables a traditional coil driven tachometer to use a 5 to 15V square wave signal that is generated my a modern ECUs. Most common use for this converter is Pre 1993 Volkswagens and pre 1996 Toyotas

CAD $49.95

USD $39.95

Instruction Manuals Hasenwerk Digital to Analog Tachometer Converter V2

VW Tachometer Adapter
Hasenwerk Digital to Analog Tachometer Converter

Hasenwerk Brake Switch Synchronizer

Volkswagen ECUs have two brake inputs and they must switch at the same time or else you will have an implausible input and the ECU will no longer be happy. This silent solid state switch will ensure that F and F47 inputs will switch states at the same time and take considerable less space and than a traditional relay would!

CAD $19.95

USD $14.95

Instruction Manuals Hasenwerk Brake Switch Synchronizer

Brake Synchronizer
Hasenwerk Brake Switch Synchronizer

Hasenwerk CCS Korrekt

Volkswagen ECUs after 1999.5 have Cruise Control System pedal logic that is "backwards" to most older vehicles. This tiny - 5 x 3.5 x 2cm - signal processor reverses the old pedal logic and makes it compatible with the new ECUs. It also ensures that both the brake pedal and brake light inputs on the ECU switch at the same time for 100% error free operation.

Input Output
Clutch Off (open or ground) F36 12V
Clutch pressed (12V) F36 GND
Brake Off (open or ground) F
F47
GND
12V
Brake pressed (12V) F
F47
12V
GND

CAD $49.95

USD $39.95

Instruction Manuals Hasenwerk CCS Korrekt
CSS Korrekt
Hasenwerk CCS Korrekt

Hasenwerk VSS Korrekt
Speed Signal Calibrator

VSS Korrekt is a small, economic, simple, effective, high quality speed signal calibration box designed to scale up or down a tachometer or speedometer signal from 0.10X to 10X *. Adjustments are made by turning a 10 turn (3600 degree) dial for ultra precise calibration in 1024 steps.

Four simple connections:
12V switched
Ground
VSS-in (5 to 15V square wave)
VSS-out (12V square wave, 5V special order)

Controls:
10 turn dial, 1024 steps between lowest and highest values

IMPORTANT NOTES:
* We can make custom calibration ranges. Please specify in the PayPal notes if you need a different range otherwise the range 0.10X to 10X will be sent.

Click here for Vehicle Speed Sensors

CAD $64.95

USD $49.95

Instruction Manuals Hasenwerk VSS Korrekt V2.0

VSS Korrekt
VSS Korrekt

Hasenwerk VSS Korrekt^2
Speed Signal Calibrator

This is the same as the VSS Korrekt, only that it has two outputs at a set differential apart from each other.

Example:
Ford Ranger Speedometer: 1.38Hz = 1km/h
Volkswagen ECU: 1.0Hz = 1km/h

Five simple connections:
12V switched
Ground
VSS-in (5 to 15V square wave)
VSS-out-1 (5V or 12V square wave x calibration)
VSS-out-2 (5V or 12V square wave x calibration x ratio)

Controls:
10 turn dial, 1024 steps between lowest and highest values

IMPORTANT NOTES:
* Please specify when ordering in the PayPal notes the ratio between VSS-out-1 and VSS-out-2, else we will send you 1.00:1.38 to match a Ford Ranger / Explorer.
We can make custom calibration ranges. Please specify in the PayPal notes if you need a different range otherwise the range 0.10X to 10X will be sent.

Click here for Vehicle Speed Sensors

CAD $84.95

USD $64.95

Instruction Manuals Hasenwerk VSS Korrekt^2 V2.0
VSS Korrekt
VSS Korrekt^2

Digital to Analong Speedometer Adapter

This adapter will make your cable driven Volkswagen speedometer run off of a VSS signal generated by a hall sensor.

Applications for this include Volkswagen MK1 and MK2 that are converted to 02A and 02J transmissions and Volkswagen Vanagons that are converted to run on Audi quattro gearboxes. Volkswagen Syncro owners who are running larger tires could use this in conjunction with our universal VSS to get 100% accurate speed on their speedometers.

Included in the kit is:

- Electronic controller
- Motor with machined adapter to speedometer
- Interfacing cable

CAD $TBA

USD $TBA

Please email us to order.

Instruction Manuals Manual Coming soon!
New Product ! ! !DigitalToAnalongSpeedometer1
DigitaltoAnalogSpeedometer
Digital to Analong Speedometer Converter

Hasenwerk Fuel Level Adapter

We have a lot of customers who want to use 2000 and later Volkswagen instrument pods in their older Volkswagens. The problem is the fuel level sensor is "backwards" after the introduction of the MK4. If you install a MK4 instrument pod in your Volkswagen Vanagon, the fuel gauge will read empty when the tank if full and full when the tank is empty.

This converter will enable your fuel level gauge to be correct when using a 2000+ instrument pod in a 1999 and older Volkswagens.

CAD $64.95

USD $49.95

Please email us to order.

Instruction Manuals Manual Coming soon!

 

Hasenwerk Ford Cruise Control Adapter

Converts Ford and Mercury steering wheels with two cruise control wires to be used with a conventional cruise control system with on/off | set | resume functions.

More Information

 
Signal Processors
Canadian Customers
Signal Processors
USA / Int'l Customers